
The ISDN switch off: what else is on your line besides the phones
Most conversations about the ISDN switch off are about the phone system. That is the easy part. The work is in the devices that dial out or send data over a copper line by themselves: the lift alarm, the intruder alarm, an old card terminal, the fax and the telemetry in the plant room. They stop quietly when the line goes, and nobody notices until it matters.
In the ISDN switch off the phones are the easy part. The risk is in lift alarms, intruder and fire alarms, card terminals, fax machines and telemetry that use the same line.
A copper line was powered from the exchange and kept working in a power cut. Fibre and IP do not; they need battery backup on site, or a SIM in the device itself.
In the UK, Openreach and BT have set the end of January 2027 for the national switch off. Start with the lift and alarm companies, because their schedules are longer than yours.
What is actually being switched off
The copper network is the old telephone network: the copper pair that runs from the local exchange into your building. Two services run over it and both are going. The analogue line, usually called PSTN, carries one call at a time. ISDN is the digital version with two or more channels, and for years it was the standard way to connect a business phone system.
In the UK, Openreach is withdrawing both and moving customers to digital lines over fibre or broadband, with BT calling its replacement Digital Voice. The national end date for the PSTN and ISDN switch off is the end of January 2027. Other providers on the Openreach network follow the same timetable, and providers on their own networks have their own.
For the phones this is a well-known migration. For everything that rides on the line, it is a different story, because those devices were built on the assumption that there would always be a dial tone.
What is on your line besides the phones
The first step in the ISDN switch off is a list, per building, of everything that uses a line. Start where the line enters the building and follow the cables, then check the contracts. These are the devices we find most often:
- The lift alarm. The button in the lift car calls a monitoring centre or a callout service. A lift without a working alarm line should not stay in service.
- Intruder and fire alarms. The alarm panel dials an alarm receiving centre. For a fire system that connection may be tied to your insurance.
- Card terminals. Older terminals dial in over an analogue line. Most have moved to IP or a SIM, but not all of them.
- The fax. Often forgotten, except by the one team or the one supplier that still sends orders with it.
- Telemetry and building management. Pumps, cold rooms, the building management system, a standby generator, or a meter that dials in its readings.
- Door entry and emergency phones. A gate intercom that diverts to a mobile, an emergency phone in a cold store or on a car park deck.
Record for each device who owns it, who maintains it and which number it calls. That last question matters more than it seems: the maintainer needs to know where the device will call after the change, and how.
What replaces each device
There is no single replacement for everything. There are three routes, and the maintainer of each device decides which one fits.
- A SIM in the device. For lift alarms and alarm panels, a cellular dialler or a module with its own SIM is often the cleanest answer: the device no longer depends on your phones or your broadband. Check the signal in the lift shaft or the basement.
- An IP connection with a second path. Modern alarm panels signal over the internet and fall back to mobile when it fails. That dual path is now standard practice in security, and it is better than anything the copper line offered.
- An analogue adapter. A small box that provides an analogue port on an IP connection. It works for an ordinary handset or a simple intercom. For fax and for devices that send data as tones it is unreliable, because those signals survive the conversion to voice over the internet badly.
The fax is usually the easiest: replace it with fax to email, or ask the one supplier who still relies on it to use email. The card terminal belongs to your payment provider; ask them for a terminal on IP or SIM. For the network underneath, the router and the cabling, the same checklist applies as for business internet.
Power cuts: what the copper line gave you for free
A copper phone line was powered from the exchange. When the building lost power, the phone kept working and the alarm panel could still call out. Fibre and IP do not. The fibre terminal, the router and the switch all need power, and without power there is no line.
That is exactly the moment an alarm needs to call. Three questions to answer before the copper line goes:
- How long must it work without mains power? An alarm panel usually has its own battery. The router and the fibre terminal do not; put them on a small UPS if alarm signals run over that connection.
- Which path is left? A device with its own SIM keeps working for as long as its battery lasts, independent of your office network. That is why the SIM route is preferred for alarms.
- Can people still call 999? At a site with no fixed line and poor mobile coverage that is not a theoretical question. Decide which handset works in that case.
The ISDN switch off in the right order
The most common mistake is to start with the phones and let the rest trail behind. Reverse it.
- First the inventory. Per building, with owner, maintainer and number called. Look for lines you pay for and no longer use; cancel those straight away.
- Then the maintainers. The lift, alarm and building management companies and the payment provider each get the question of how their device will connect and when they can attend. Their lead times are usually longer than your IT’s.
- Then the network. The connection, the router, the battery backup and, where needed, an analogue adapter in a fixed and documented place.
- Then the phones. The phone system, with your numbers ported. How that part runs is in our article on switching business phone system.
- Cancel last. Cancelling a copper line before the device on it has been moved and tested is the only step in this list you cannot undo.
Test, and write down what you tested
A lift alarm that does not get through will not show up in an ordinary week. Test every converted device with the party at the other end, not just whether the box has a light on.
- Make the alarm actually signal. Ask the monitoring centre to confirm the signal arrived, with the right address and the right code.
- Test with the power off. Unplug the router and check that the device still signals over its second path.
- Call in and call out. An intercom that can call but cannot be called is doing half its job.
- Record it. What was converted, how it connects now, who maintains it and when it was tested. At the next refurbishment or change of supplier, that is the only document anyone looks for.
Where our work stops
We do not supply line rental, numbers or call minutes. The line and the network behind it belong to the operator; the contract, the numbers and the cancellation go through that operator. We advise on the connection that replaces it and can supply it, but the fibre or the copper pair itself belongs to the network operator.
We do not run the alarm receiving centre and we do not maintain lifts or alarm systems. How a lift alarm or alarm panel is connected is decided by the company that maintains it, and that company is responsible for its inspection. The card terminal comes from your payment provider. What we do: the inventory, the network, the router and battery backup, analogue adapters where they fit, the phone system, and testing together with those companies.
Questions we get about this
The five that come up most during the ISDN switch off.
When is the ISDN switch off in the UK?
Openreach and BT have set the end of January 2027 for the national PSTN and ISDN switch off, with areas moving in stages before that. Providers on other networks run their own schedules. Ask your provider for the date at your address, and about lines you do not use for calls.
Will my lift alarm still work after the PSTN switch off?
Not by itself. A lift alarm that calls over a copper line stops working when that line is withdrawn. Ask the lift maintenance company to convert it, usually to a module with its own SIM, and then test with the monitoring centre that the call actually arrives.
Can a fax machine work over a digital line?
Sometimes, but not reliably. A fax sends data as tones, and those survive the conversion to voice over the internet badly. Fax to email is usually the better answer, or agreeing with the one party still faxing that they use email instead.
What happens in a power cut without a copper line?
A copper line was powered from the exchange and kept working. Fibre and IP need power in the building. Put the router and fibre terminal on a UPS if alarm signals use that connection, or give the alarm its own SIM so it does not depend on your network.
Do you supply the line rental and the numbers?
No. We do not supply line rental, numbers or call minutes; those stay with the operator, and the line itself belongs to the operator. We handle the inventory, the network, the battery backup, the phone system and testing together with the lift and alarm maintainers.
Further reading
The services this migration connects to.
Shall we map your lines with you?
Send us what you know about the lines in each building and what is connected to them. We complete the inventory, prepare the network and test together with the lift and alarm companies.
Practical IT knowledge in your inbox
New guides on management, security and the workplace, written by the people doing the work. No sales talk, and you can unsubscribe in one click.