
WiFi 6, 6E or 7 in the office: what the standard changes and when to replace your access points
WiFi 6 is sold on headline speeds nobody reaches in an office. What the standard does change is how an access point copes with many devices at once, and that is where the gain lies. This piece explains what WiFi 6, 6E and 7 really add, what your laptops notice and how to decide whether your access points are due for replacement.
WiFi 6 mainly makes an access point better at handling many devices at once; the headline speed on the box is not the figure that matters in an office.
WiFi 6E and 7 add the 6 GHz band, but only laptops and phones that support 6 GHz get anything from it.
Replace access points for a reason: end of updates, measured complaints or a new layout, and include the switch, PoE and cabling behind them. Mains power is work for the electrician.
What WiFi 6 changes: more devices at once, not mainly more speed
WiFi 6 is the Wi-Fi Alliance’s name for the IEEE standard 802.11ax. It uses the same bands as its predecessor, 2.4 and 5 GHz, and the big change is not the maximum speed but the way the access point shares airtime.
- OFDMA. An access point can split one transmission and serve several devices at once, rather than working through them one by one. It helps most with lots of small traffic: chat, voice, sensors.
- MU-MIMO in both directions. Several devices at once, now also from device to access point. You notice it in video meetings, where everyone sends video too.
- BSS colouring. Access points that hear each other on the same channel can recognise each other’s traffic and wait less. In an open-plan office with access points close together, that is the quiet gain.
- Target Wake Time. Devices agree when to wake up. It saves battery on phones, scanners and sensors.
The figure on the box is the theoretical total capacity of all radios combined. What one laptop gets on an ordinary working day is far below that, and depends more on distance, walls and the number of neighbours than on the standard.
WiFi 6E: the 6 GHz band and how much of it Europe allows
WiFi 6E is WiFi 6 with a third band added: 6 GHz. That is new, still empty space, with no legacy devices, no canteen microwave and far more channels. In a busy building, that is the real case for 6E.
In the European Union and the United Kingdom only the lower part of the 6 GHz band has been opened up, roughly 5.9 to 6.4 GHz, and fixed access points may only use it indoors and at limited power. That is enough for six 80 MHz channels, but less than American articles about 6E describe. Read those with that difference in mind.
Two practical consequences:
- Slightly shorter range. 6 GHz is attenuated more by walls and glass than 5 GHz. In an open office it hardly matters; in a building with many concrete walls it means more access points or different placement.
- WPA3 only. WPA3 is mandatory on 6 GHz. Devices that only know WPA2 cannot join and stay on 2.4 and 5 GHz.
And WiFi 7: what it adds and what you notice in the office
WiFi 7 (IEEE 802.11be) builds on 6E. The two additions that matter in an office:
- Multi-link operation. A device can be connected over two bands at once, say 5 and 6 GHz, and switches without interruption when one gets busy. That mainly makes the connection more stable.
- 320 MHz channels. On paper the biggest step. In Europe the available 6 GHz space fits only one channel of that width, and in a building with several access points one channel is not usable. In practice an office runs on narrower channels.
So WiFi 7 is no reason to replace access points that are still fine. If you are replacing anyway, it is worth comparing, but look mainly at how long the vendor will support the model with updates and what it needs in power and uplink. That is where the long-term difference lies, not in the headline speed.
Your laptops and phones decide the gain
An access point talks to every device in the language that device speaks. A laptop with a WiFi 5 card under a WiFi 6 access point stays a WiFi 5 laptop, and the new techniques only work for devices that know them. The gain therefore only arrives once most of your devices take part.
- Check what is connected now. The controller or cloud portal of your access points shows per device which standard and band it uses. That is a better source than a guess about the laptop fleet.
- 6 GHz needs more than the wifi card. On Windows laptops, 6 GHz only works with Windows 11 and a driver that supports it. A 6E card in a laptop running Windows 10 stays on 5 GHz.
- Do not forget fixed devices. Handheld scanners, card terminals, printers and sensors are rarely replaced and often speak an older standard, sometimes 2.4 GHz only. That band therefore stays necessary.
A sensible order is: let the laptop fleet move up through natural replacement first, then the access points. Or the other way round if the network is the complaint now; either works, as long as you know what to expect.
When to replace access points, and when not to
A new standard is not a reason in itself. These triggers are:
- Updates have stopped. An access point that no longer receives security updates sits on your network with known vulnerabilities. That is the hardest reason, and the vendor publishes the date in advance.
- Measured complaints at busy times. Connections dropping in the meeting room or canteen when it is full, which a survey traces to capacity rather than coverage. If it is coverage, different placement often helps more than a new model.
- A new layout or refurbishment. New walls, different occupancy or an extra floor change the plan. Replacing is then often more sensible than moving.
- Security that can no longer move on. Older access points sometimes do not support WPA3. If you want to move to stronger security, that is where you get stuck.
- A licence or controller reaching its end. With systems that rely on a cloud portal or controller, the end of that support is often the real moment.
If the network works, the access points get updates and nobody complains, waiting for one of these triggers is a defensible choice. If you do not know where the complaints come from, start with a WiFi analysis.
What has to change behind the access point
A new access point often asks more of the cabling and the switch than the old one. It is the item most often overlooked in a replacement:
- Power. Access points for WiFi 6E and 7 have more radios and draw more power over the cable, often PoE+ and for the heaviest models 802.3bt. A switch that easily powered the old access points may now fall short; an access point that gets too little sometimes starts with some of its radios off.
- Port speed. An access point of this generation can deliver more traffic than a 1 Gbit/s port passes on. Switch ports at 2.5 or 5 Gbit/s generally run over existing Cat5e or Cat6 cable; 10 Gbit/s needs Cat6A.
- The uplink and the internet line. Faster wifi moves the bottleneck to the links between switches and to the internet connection. Look at those too, or nobody will notice the replacement.
What that means for the switch itself, and why you want a manageable model there, is in our article on managed vs unmanaged switches.
A replacement in four steps
- 1. Measure. A survey of the current network: where coverage is weak, where it is busy, which channels the neighbours use and which devices are connected. Without that survey you replace by feel.
- 2. Design. The number of access points and where they go, the channel plan per band, and whether 6 GHz gets its own network name or is offered together with 5 GHz. Plus the power and port-speed sum per switch.
- 3. Roll out floor by floor. One zone at a time, outside office hours, with the old access points as a fallback until the new ones are tested. Run WPA3 in transition mode while there are still devices that do not support it.
- 4. Re-measure and tidy up. A second survey with real devices, not only the survey laptop. Then the old access points come off the network, out of the management portal and out of the asset register, and are disposed of with their configuration wiped.
Most troublesome rollouts stall on a skipped step 2: the same numbers in the same places, while a new access point makes different demands on channels and placement.
Where our work stops
What we do. We survey the existing network, design the new one, supply the access points and switches, install the data cabling, mount the access points, configure networks, security and channels, and then manage it with monitoring and firmware updates. Old equipment is disposed of with its configuration wiped.
What we do not do. Mains power is work for a qualified electrician. If the PoE load in the network cabinet goes up and an extra circuit or socket is needed, the electrician installs it, under BS 7671 in the UK. Cooling the plant room is not network work either. We do tell you how much power and heat the new equipment needs, so the electrician knows what to install for.
Questions we get about this
The five that come up most often.
What is WiFi 6?
WiFi 6 is the name for the IEEE standard 802.11ax. It uses 2.4 and 5 GHz and mainly makes an access point better at serving many devices at once, with techniques such as OFDMA, two-way MU-MIMO and BSS colouring. The higher headline speed on the packaging is theoretical and rarely reached in an office.
What is the difference between WiFi 6 and WiFi 6E?
WiFi 6E is WiFi 6 with the 6 GHz band added. That band is quieter and has more channels, but has slightly shorter range through walls and requires WPA3. In the EU and the UK only the lower part of the band is available, and only devices with 6E support can use it.
Is WiFi 7 worth it in the office yet?
If you are replacing anyway, it is worth comparing; if your access points are still fine and receive updates, WiFi 7 is no reason to replace them. The most useful addition in an office is multi-link operation for a more stable connection. The wide 320 MHz channels are hardly usable in a European office.
When should you replace access points?
When they no longer receive security updates, when surveys show they cannot handle busy periods, with a new layout or refurbishment, or when the licence or controller reaches its end. A new standard alone is not a reason. If there are complaints, first measure whether the issue is coverage or capacity.
Do you also sort out power for new access points?
Power over the network cable, via PoE from the switch, is ours. An extra circuit or socket in the network cabinet is work for a qualified electrician, under BS 7671 in the UK. We tell you how much power the equipment needs.
Further reading
What this choice connects to.
Shall we check whether your access points can stay?
Send us the models of access points and switches you have now and where the complaints are. We will tell you whether replacing makes sense now, what has to change behind the access point and whether a survey should come first.
Practical IT knowledge in your inbox
New guides on management, security and the workplace, written by the people doing the work. No sales talk, and you can unsubscribe in one click.